LxCenter Forum: General Development » Old versions, releases and decoder software

HyperVM & Kloxo Support

Forum

Members

Help

Home

Home » Development Forums » General Development » Old versions, releases and decoder software

Show: Today's Messages :: Show Polls :: Message Navigator

Old versions, releases and decoder software [message #73952]

Thu, 15 April 2010 10:39

com2

Messages: 1119
Registered: August 2007
Location: Spain

Senior Master
Developer

Looking at one of the issues I believe that the SVN version of Kloxo is a snapshot in the middle of development phase. I believe that some driver changes were interrupted in the middle and some of it might even have crept pre-maturely into present release.

My questions:

What happened to the original plan to have the complete harddisks of the developer available? Is there a way to get hold of the original CVS dev repositry he was using?
Are there still old release versions backed up somewhere? This could be a second option to go back to a still working release and use a decoder to find out what the code was.
What software would decode these old releases?

Report message to a moderator

Re: Old versions, releases and decoder software [message #73969 is a reply to message #73952]

Thu, 15 April 2010 17:37

LxCenter_Danny

Messages: 2068
Registered: July 2007
Location: Netherlands

Grandmaster
LxCenter Core Team Member
LxCenter Representative

com2 wrote on Thu, 15 April 2010 16:39

Looking at one of the issues I believe that the SVN version of Kloxo is a snapshot in the middle of development phase. I believe that some driver changes were interrupted in the middle and some of it might even have crept pre-maturely into present release.

My questions:

What happened to the original plan to have the complete harddisks of the developer available? Is there a way to get hold of the original CVS dev repositry he was using?

Are there still old release versions backed up somewhere? This could be a second option to go back to a still working release and use a decoder to find out what the code was.

What software would decode these old releases?

1. Dont ask again. We have to do without it and we are further than the old state so that would mean going back to zero.
The SVN versions are running and confirmed. Just some minor issues. When we are ready and a TEST version is aviable then you can test too. I wrote a article at the wiki site how you can run the current SVN version.

2. SVN versions are working. No point to break the law by decoding copyrighted software Razz

Kloxo:
kloxo-6.0.2042.zip kloxo-6.0.2062.zip kloxo-6.0.2082.zip kloxo-6.0.2052.zip kloxo-6.0.2072.zip kloxo-6.0.2083.zip
hypervm-2.0.7942.zip
hypervm-2.0.7952.zip lxadmin-5.0.16242.zip
hypervm-2.0.7962.zip lxadmin-5.0.16252.zip
hypervm-2.0.7982.zip lxadmin-5.0.16262.zip
hypervm-2.0.7992.zip lxadmin-5.0.16272.zip

3. There is no decoding software. If you want to decode it, you need to pay for the service at zend company.
Yes, i know there are illegal ways. Thats not what we want to do. Bad image!

Again, it is asked too much now and answers are given at the forum, irc, email (lists) etc in the past.

SVN versions are working, minor issues, no need for CVS/HDD's.
Its too old information already.

LxCenter - System Operations

Report message to a moderator

Previous Topic:	Where o where?
Next Topic:	any chance to edit the source?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun May 19 06:24:49 EDT 2013

Total time taken to generate the page: 0.35523 seconds

.:: Contact :: Home :: Privacy ::.

Click here to lend your support to: LxCenter and make a donation at www.pledgie.com !