LxCenter HyperVM & Kloxo Support

Forum



Members   Search      Help    Register    Login    Home
Home » HyperVM Community Support » Knowledge Base » Preparing a node for configuring vps
Re: Preparing a node for configuring vps [message #48463 is a reply to message #48407] Mon, 01 December 2008 14:12 Go to previous messageGo to next message
Michele is currently offline Michele  Italy
Messages: 76
Registered: May 2008
Location: Italy
Valuable Member
Hi
After restarting the server this was unreachable so I had to reset and reinstall Centos. Now i'm going to setup hypervm again.
I'll try it.

Report message to a moderator

Re: Preparing a node for configuring vps [message #48480 is a reply to message #48463] Mon, 01 December 2008 18:12 Go to previous messageGo to next message
Michele is currently offline Michele  Italy
Messages: 76
Registered: May 2008
Location: Italy
Valuable Member
Hi
Reading forum I found this is probably for LVM setup that I don't know how to. I have centos by provider os template. I don't know those partition stuff, but I can try. Is it possible to do this via ssh? and using wich utility/command?
I know someone could laugh for this but I've no other solution as now. Thank for anyone help/suggestion.

Report message to a moderator

Re: Preparing a node for configuring vps [message #48485 is a reply to message #48480] Mon, 01 December 2008 20:46 Go to previous messageGo to next message
Michele is currently offline Michele  Italy
Messages: 76
Registered: May 2008
Location: Italy
Valuable Member
Hi
I've found that i can set lvm and disk partition on my server trough a livecd system.
I've found this howto: http://www.debuntu.org/how-to-install-ubuntu-over-lvm-filesy stem in wich there is a part about setting up lvm and partitions.
Is it a good guide for hypervm lvm requirements?

Report message to a moderator

Re: Preparing a node for configuring vps [message #51202 is a reply to message #48485] Mon, 22 December 2008 10:48 Go to previous messageGo to next message
Lxhelp
Messages: 23691
Registered: July 2006
The Champion
HyperVM needs FREE LV, that's about it. You don't need to do anything special at all.

thanks.


On Tue, Dec 02, 2008 at 01:46:32AM -0000, Michele Piperis wrote:
>
>
> Hi
> I've found that i can set lvm and disk partition on my server trough a livecd system.
> I've found this howto: http://www.debuntu.org/how-to-install-ubuntu-over-lvm-filesy stem in wich there is a part about setting up lvm and partitions.

Report message to a moderator

Re: Preparing a node for configuring vps [message #51209 is a reply to message #48405] Mon, 22 December 2008 11:04 Go to previous message
Lxhelp
Messages: 23691
Registered: July 2006
The Champion
You have to first boot into the xen kernel and then run:

 
 /script/fixxenkernel


thanks.


On Mon, Dec 01, 2008 at 10:24:25AM -0000, Michele Piperis wrote:
>
>
> Hi, I'm using this step guide but have a problem
> rfhmendes wrote on Sat, 07 June 2008 16:15
> > Now, run:
> > cd /usr/local/lxlabs/hypervm/httpdocs/
> > lphp.exe ../bin/misc/fixcentos5xen.php
>


Report message to a moderator

Previous Topic:Importing vpses from another master
Next Topic:APF and HyperVM
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Wed Jun 19 17:58:48 EDT 2013

Total time taken to generate the page: 0.06089 seconds
.:: Contact :: Home :: Privacy ::.

Click here to lend your support to: LxCenter and make a donation at www.pledgie.com !

Powered by: FUDforum 3.0.2.
Copyright ©2001-2010 FUDforum Bulletin Board Software